2018 EBY TransPork 53'x102"x13'6" Spread

SPECIFICATIONS:
-LENGTH: 53'

-WIDTH: 102"
-HEIGHT: 13'6"
-KING PIN: 36" DEEP, 49" HIGH
-FRONT DROP: 6"
-LANDING GEAR: CRANK STYLE

-----RUNNING GEAR-----
-SUSPENSION: HENDRICKSON AIR RIDE - SU15512 INTSUSP.33288
--TIREMAXX INFLATION - SU15438

-DUMP VALVE: MANUAL W/ PRESSURE GAUGE
--ELECTRONIC DUMP ON REAR AXLE. WIRE TO AUX

-AXLE CONFIGURATION: 10'1" SPREAD
-AXLE LOCATION: 24" TUCK
-AXLES: HENDRICKSON
-HUBS: STD
-DRUMS: NONE
-BRAKES: DISC

-ABS: 4S/2M
-WHEEL TYPE: 22.5 (4) INNER ALCOA LVL (4) OUTER DURABRITE

-TIRES: 11R22.5 GENERAL RA

-GVWR: 66,000 LBS
-----FLOOR-----
-FLOOR: .115 FLAT ALUM DIAMOND PLATE

-PERM RAMP AT 6" DROP

-FLOOR LINER: ALUMINUM UNDER MID DECK

-----FRONT END-----
-PANELS: MILL FINISHED ALUM
-EXTRUDED CORNERS: SS OVERLAY

-VENTS: 4 FULL HEIGHT WITH ADVANTAGE SLIDING

-HANDLES/STEPS TO ACCESS VENTS: NONE
-TIRE CARRIER: NONE
-LIGHTED SIGN: ALUM FRAME

-NOSE BOX: DOUBLE BOX, DOUBLE PLUG (AUX 4-PRONG)

--LOCATE IN CENTER WITH GLAD HAND ON EACH SIDE
-4 WIRE HARNESS FROM AUX TO REAR

-----REAR END-----
-ROADSIDE: NEW STYLE SPLIT ROLL UP DOOR WITH MILLED HOLES

IN EVERY POSSIBLE PANEL; SINGLE PULLEY AT BOTTOM

-CURBSIDE: PERM PANEL ADVANTAGE STYLE

-WASH OUT: CS REAR LOWER
-TOW HOOKS: (2)

-BUMPERS VERTICAL: (2) 13" x 3" ON CORNERS

-ADD (2) 48" VERTICAL ON ROLL UP SIDES

-BUMPERS HORIZONTAL: FULL WIDTH 4"
-----ROOF-----
-MATERIAL: ALUM
-HATCH: (5) TOTAL.

(1) EACH IN FRONT TWO COMPTS CENTERED. (1) REAR COMPT CENTERED.
(2) IN 3RD COMPT W/ (1) JUST BEHIND DIVIDER AND (1) JUST AHEAD OF REAR PARTITION.
-ROOF LINER: ALUMINUM

-----SIDE ASSEMBLY-----
-HOLE PATTERN: ADVANTAGE SIDES, FRONT, AND REAR

--USE HUCKS NOT BOLTS TO FASTEN SIDE HANDLE ASSEMBLY TO BOTTOM RAILS
-PANEL RETAINER CLIPS: NONE
-CENTER SIDE DOORS: (2) 28-1/2" WIDE
--ADD HOLD BACK LATCHES TO STORE OPEN

--NOTE: ADD LADDER RUNGS BEHIND MID SIDE DOORS
-REAR SIDE DOORS: YES WITH FOLD LADDER

--LOWER INSIDE LATCH (2) RIVET ROWS FROM STD
--ADD RUBBER STOPS BEHIND LADDER WHEN DOWN
-----CLOSURE SYSTEMS-----
-CLOSURE PANELS: ADVANTAGE SLIDING

-PLUGS: NONE
-----TOP DECK-----
-GATES: (2) TUBE TO MAKE (4) COMPARTMENTS
-GATE TYPE: TUBE STYLE. SET AT 4" UP
-FUNNEL GATE: TUBE STYLE IN FRONT OF REAR PARTITION
-----BOTTOM DECK-----
-GATES: (2) TUBE TO MAKE (4) COMPARTMENTS
-GATE TYPE: TUBE STYLE. SET AT 4" UP
-----REAR PARTITION-----
-ROADSIDE TOP: 1/2 SWING, TUBE STYLE
-CURBSIDE TOP: 1/2 SWING, TUBE STYLE
-ROADSIDE BOTTOM: 1/2 SWING, TUBE STYLE
-CURBSIDE BOTTOM: 1/2 SWING, TUBE STYLE
-----REAR COMPARTMENT-----
-LENGTH: 14'6" MOVE REAR PARTITION AHEAD (1) POST FROM STD
-PULL-OUT CHUTE: 156" LONG DP, 1"ON 5" CENTERS

-CHUTE SIDE: 6' FRONT SWING, 6' REAR SWING, TUBE GATES AND FENCE
-JAIL HOUSE: TUBE STYLE PERM FENCE TO MAKE 1/2 JAIL
-----LIGHTS-----
-SIDE LIGHTS: (7) TOP & (7) BOTTOM PENNY STYLE

-SIDE REAR POST: (7) PENNY

-REAR HEADER: (3) BRAKE, CLEARANCE
-REAR POST: (2) HIGH MOUNT TURN, CLEARANCE
-BUCK PLATE: (2) BRAKE, CLEARANCE, (1) TURN, CLEARANCE EACH SIDE
-INSIDE LIGHTS: (9), LOCATE ALL RS EXCEPT JAIL
-BACK UPS: (2) WIRE TO AUX

-----MISCELLANEOUS-----
-MUD FLAPS: HD BLACK RUBBER CUT 4" SHORTER THAN STD

-STAINLESS STEEL WEIGHTS TO READ JWV

-CLOSURE STORAGE: NONE
-TOOL BOX: (2) 48'X18"X24" EACH SIDE INSIDE SPREAD

--NEEDS TO HAUL (2) SHAVINGS BALES PER SIDE
-SOLD BY STICKER: M.H. EBY, INC.